FEATURED
30A ESC – Electronic Speed Controller with Dean Connector
Specifications:
- Model: 30A BLDC ESC
- Colour: Yellow
- Continuous Current: 30A
- Burst Current: 40A
- Voltage: 7.4V-11.1V (2-3S LiPo)
- BEC Output: 5V/3A
- Connector: Dean Connector
- Firmware: SimonK ESC
- Li-Po battery: 2S ~ 3S
- Application: Drones, RC Cars, Boats
- Features: Lightweight, Compact Design
- Size: 45mm x 24mm x 9mm
- Weight: 23g
Package Includes:
1 x 30A BLDC ESC Electronic Speed Controller with Connectors
1000KV BLDC Motor A2212 with Soldered Bullet Connector
Specifications:
- Model: A2212
- KV Rating: 1000KV
- Type: Brushless
- Connector: Soldered Bullet Connector
- Shaft Diameter: 3.17mm
- Recommended Voltage: 11.1V
- Maximum Continuous Current: 13A
- Maximum Continuous Power: 143W
- Maximum Efficiency Current: 4-10A (75%)
- Internal Resistance: 0.105 ohms
- Recommended Propeller Size: 8-10 inches
- Wire Length: 150mm
- Motor Dimensions: 27.5 x 27mm
- Weight: 47g
Package Includes:
1 x 1000Kv Brushless Motor for Drone 1 x Prop Adapter A Motor Holder (X-type) and a set of screws
30A ESC Simonk Electronic Speed Controller with Dean Connector
Specifications:
- Model: 30A ESC Simonk
- Type: Electronic Speed Controller
- Continuous Current: 30A
- Burst Current: 40A
- Suitable Lipo Batteries: 2 ~ 3S
- BEC Output: 5V / 2A
- Connector Type: Dean Connector
- Usage: DIY Drone, RC planes, multirotors
- Dimensions: 34mm x 24mm x 9mm
- Weight: 23g
Package Includes:
1 x Simonk 30A BLDC ESC Electronic Speed Controller
F450 Tri Colour Quadcopter Frame with PCB Board VT400
Specifications:
- Frame Type: Quadcopter Frame
- Model: F450
- Color: Tri-color (Orange and Green)
- Material: Glass Fiber, Polyamide-Nylon
- PCB Board: Included
- Wheelbase: 450mm
- Arm Size: 220 x 40 mm (L x W)
- Motor Mount Hole Diameter: 3mm
- Dimensions: 450 x 55 mm (H x W)
- Weight: 295g
Package Includes:
1 x F450 Tri-Color Made In INDIA Quadcopter Frame 1 x PCB Board 2 x Orange arms 2 x Green Arms Set of Screws Unboxing Video of Drone Frame
2200mAH Lipo Battery 11.1v for Quadcopter Plane Multirotor
Specifications:
- Capacity: 2200mAh
- Voltage: 11.1V
- Battery Type: Lithium Ion (Li-ion)
- Configuration: 3S (3 cells in series)
- Discharge Rate: 30C (continuous)
- Charge Rate: 1 ~ 3 C
- Discharge Plug: XT-60
- Balance Plug: JST-XH
- Max. Burst Discharge: 60C (132.0A)
- Max. Charge Rate: 5 C
- Max. Continuous Discharge: 30C(66.0A)
- Dimensions: 106mm x 34mm x 23mm
- Weight: 175g
Package Includes:
1 x 2200mAH Lipo Battery 11.1v for Quadcopter Plane Multirotor
30A ESC Simonk Electronic Speed Controller with Connector (Set of 4)
Specifications:
- Model: SimonK 30A ESC
- Current Rating: 30A
- Voltage Range: 2-4S LiPo
- Burst Current: 40A
- Constant Current: 30A
- BEC Output: 5V/2A
- Firmware: SimonK
- Operating Temperature: -10°C to 85°C
- Colour: Red
- Dimensions: 45 x 25 x 8mm (LxWxH)
- Weight: 25g (each)
Package Includes:
4 x Simonk 30A BLDC ESC Electronic Speed Controller
1000KV BLDC Motor with Soldered Bullet Connector (Set of 4)
Specifications:
- Motor Type: 1000kv brushless motor
- KV Rating: 1000KV
- Operating Voltage: 7.4V to 11.1V
- Shaft Diameter: 3.17mm
- Current Handle Capacity: 12A
- No-Load Current: 500 mA
- Max. Efficiency Current: 4 ~ 10 A
- Compatible LiPO Batteries: 2S ~ 3S
- Connector Type: Pre-soldered bullet connectors
- Mounting: Suitable for standard motor mounts
- Dimensions:Â 27.5 x 24 mm
- Weight: 64 g
Package Includes:
4 x A2212 1000Kv Brushless Motor for Drone 4 x Prop Adapter A Motor Holder (X-type) and a set of screws
1045/1045R 10 inch Propeller Pair (CW+CCW), Black
Specifications:
- Prop. Diameter: 10 inch
- Length: 10 inch
- Pitch: 4.5 inch
- Shaft Diameter: 9.5 mm
- Total Length: 10 inch / 254 mm
- Material: Carbon Nylon
- Plastic Reducers: 2.75, 3, 3.17, 4, 4.70, 5, 6, 6.25
- Rotation Direction: CW, CCW
- Rotation: 1CW+1CCW
- No. of Blades: 2
- Weight: 28 g
Package Includes:
1 x Counter-Clockwise (CCW) Propellers 1045 (10×4.5) 1 x Clockwise (CW) Propellers 1045 (10×4.5) Set of Prop Reducers
HOT DEALS
L293D Motor Driver Shield Or Servo Shield For Arduino
Original price was: ₹599.00.₹199.00Current price is: ₹199.00.
Arduino Uno R3 Development Board ATmega328P with USB Cable
Original price was: ₹1,299.00.₹899.00Current price is: ₹899.00.
L298N Motor Driver Module with PWM Control
Original price was: ₹499.00.₹189.00Current price is: ₹189.00.KITS
CATEGORIES
PIR Sensor HC-SR501 Motion Detector Pyroelectric Infrared Module
Specifications:
- Model: PIR HC-SR501
- Operating Voltage: 4.5 ~ 20 VDC
- Current Consumption: 0.06 mA
- Detection Range: Up to 7 meters
- Detection Angle: <140°
- Output Signal: High (3.3V) when motion is detected, Low (0V) when no motion is detected
- Time Delay Adjustment: 5 to 200 seconds
- Trigger Mode: Repeatable (default) or Non-repeatable (jumper selectable)
- Dimensions: 32mm x 24mm x 25mm
- Weight: 10g
Package Includes:
1 x HC-SR501 PIR Sensor Motion Detector Pyroelectric Infrared Module
LDR Sensor LM393 Photosensitive Light Dependent Sensor
Specifications:
- Model: LM393 Light Dependent Resistor (LDR) Sensor
- Operating Voltage: 3.3V - 5V
- Output Type: Digital (0 or 1)
- Detection Range: Adjustable
- Sensitivity: High
- Operating Temperature: -40°C to 85°C
- Dimensions: 19mm x 15mm x 6mm
- Weight: 2g
- Interface: Analog/Digital
- Compatibility: Arduino, Raspberry Pi, and other microcontrollers
Package Includes:
1 x LDR Sensor LM393 Light Dependent Resistor Sensor
BMP280 Sensor Barometric Pressure and Altitude Sensor Module
Specifications:
- Model: BMP280
- Sensor Type: Barometric Pressure and Altitude Sensor
- Compatibility: ESP8266 NodeMCU, D1 Mini, Arduino Uno
- Pressure Range: 300-1100 hPa
- Altitude Range: 0-9000 meters
- Accuracy: ±1 hPa (Pressure), ±1 meter (Altitude)
- Operating Voltage: 1.8V - 3.6V
- Interface: I2C, SPI
- Operating Temperature: -40°C to +85°C
- Dimensions: 15 mm x 12 mm
- Weight: 2g
Package Includes:
1 x BMP280 Barometric Pressure and Altitude Sensor I2C/SPI Module 1 x Header set (Without Soldered)
YF-S201 Water Flow Sensor with 1-30 Liter/min Flow Rate
Specifications:
- Model: YF-S201
- Flow Rate Range: 1-30 liters per minute
- Operating Voltage: 5V
- Output Signal: Pulse
- Working Temperature: 0-80°C
- Working Pressure: ≤1.75MPa
- Accuracy: ±3%
- Material: Plastic
- Connector Type: G1/2"
- Dimensions (LxWxH): 58 x 40 x 40 mm
- Weight: 85g
Package Includes:
1 x YF-S201 Water Flow Sensor
STC 1000 Digital Temperature Controlled Thermostat Switch
Specifications:
- Model: STC-1000
- Type: Digital Temperature Controlled Thermostat Switch
- Display Type: Digital
- Temperature Control Range: -50°C to 90°C
- Temperature Resolution: 0.1°C
- Temperature Accuracy: ±1°C
- Relative Humidity: 20 to 85%
- Input Power: AC 110V-220V
- Output Power: Max. 10A, 110V-220V
- Sensor Type: NTC Sensor (10KΩ)
- Sensor Cable Length: 1 meter
- Dimensions: 60 x 40 x 25mm (LxWxH)
- Weight: 150g
Package Includes:
1 x STC-1000 AC220V Digital Temperature Controlled Thermostat Switch 1 x User Manual
TTP226 Touch Sensor 8-way Capacitive Touch Switch Module
Specifications:
- Operating Voltage: 2.4V to 5.5V
- Number of Touch Channels: 8
- Output Sink Current: 8mA
- Output Pin Pull-up Current: 4mA
- Output Type: Digital (Active Low)
- Response Time: 60ms
- Response Time (Low Power Mode): 220ms
- Operating Current: < 1.5mA
- Standby Current: < 10μA
- Operating Temperature: -40°C to 85°C
- Dimensions: 46mm x 47mm x 11mm
- Weight: 6g
Package Includes:
1 x TTP226 Touch Sensor 8-way Capacitive Touch Switch ModuleOUR RECENT BLOGS
Why Rogers Laminate Selection Cannot Be Based on Dk Alone
Technical learning article for RF, microwave, mmWave, PCB, and hardware engineers. When engineers first compare Rogers laminates, ...
ESP32 Beginner Guide: Setup, Pinout & Projects
Starting with the ESP32 development board is easier than you might think, especially if you're new to IoT or electronics. The Node...
IoT Projects for US Engineering Students: 6 Practical Ideas
The Internet of Things (IoT) is changing the way we live, work, and interact with the world. As an engineering student in the Unit...
Smart Dustbin Using Arduino & Ultrasonic Sensor: Complete Guide
The Smart Dustbin using Arduino and an Ultrasonic Sensor is an innovative IoT project simplifying waste disposal. First, it uses a...
Low-Cost Ultrasonic Sensor Projects for Beginners
Ultrasonic sensors are popular with beginners in DIY electronics because they’re affordable, easy to use, and versatile. Working w...
-
Free Delivery
For all orders over ₹499
-
7 Days Return
If goods have problems
-
Secure Payment
100% secure payment
-
24/7 Support
Dedicated support
